Body fat percentage calculator
Works out body fat percentage with a tape measure: height, neck, waist and, for women, hips. US Navy formula. Weight is needed only for fat mass.
Input
Without shoes.
Report a problem
One formula, a tape measure and an honest error
What the calculator works out
In: sex, height and two measurements – neck and waist. The female formula adds hips. Out: body fat percentage by the US Navy formula, published by Hodgdon and Beckett in 1984. Weight is optional: it is not in the formula itself and is needed only to turn the percentage into kilograms of fat and lean mass.
This is an estimate from body measurements, not a measurement. A tape does not weigh fat – it shows how far your body is shaped like the bodies the formula was fitted to. So the number here has an error of a few percentage points, and it is useful as a baseline over time, not as a diagnosis.
Why this formula
There are at least three families of methods for a tape and scales: the US Navy method from body measurements, Jackson–Pollock with callipers, and estimates derived from BMI. They give different numbers for the same body. The calculator uses the Navy formula because it needs only a tape measure, and names it on the page – so you know what you are comparing with if you get measured elsewhere.
There is deliberately no menu of three methods here. Choosing between regressions is not a question a reader can have a view on.
How to measure so the number means something
The tape sits snug but does not dig into the body. Neck – below the Adam's apple, at the narrowest point, shoulders down. Waist – at the navel for men, at the narrowest point for women. Hips – at the widest part of the buttocks. Height – without shoes.
The main source of error is the tape, not the arithmetic. Two centimetres on the waist shift the answer by about one and a half percentage points, so measure twice and take the same number. Measure in the morning, before eating, and always the same way – otherwise you are comparing ways of measuring, not your body.
Why the neck must be smaller than the waist
The formula takes a logarithm of the difference “waist minus neck”. If the neck equals the waist or is larger, the difference is zero or negative, and such a number has no logarithm. In that case the page does not plug in a minimum to force a result: it refuses and says which measurement looks swapped. Almost always it is the neck entered in the waist field, or the other way round.
The category is the ACE table, not a fact
Next to the percentage the page prints a category: “essential fat”, “athletes”, “fitness”, “average”, “obese”. The limits come from the American Council on Exercise (ACE) table and carry its name. This matters: ACSM and Jackson–Pollock publish other limits under the same words, so the category is one reading of the number, not a medical classification.
The calculator's answer is the percentage. The category is a hint to it.
What the calculator does not do
It makes no diagnosis, recommends no weight, suggests no diet and does not say how many kilograms you “should” lose. It knows nothing about muscle, swelling, pregnancy, age or where exactly the fat sits inside – and that last one matters more for health than the overall percentage. If the number worries you, talk it over with a doctor, not a calculator.
Common questions about body fat percentage
How accurate is this result?
It is an estimate with an error of a few percentage points against laboratory methods – DEXA or underwater weighing. The formula was fitted to adult US military personnel, and the further your body is from that sample, the larger the error. It works best as a way to see change over time when you measure yourself the same way.
Why are women asked for hips and men not?
That is how the formula is built: it has two versions with different coefficients, the female one reads the sum “waist plus hips minus neck” and the male one “waist minus neck”. If you entered hips with the male version, the page does not read them and shows in the “Read” row exactly what went into the calculation.
Why is weight optional?
Because it is not in the percentage formula. Weight is needed only for two extra rows – fat mass and lean mass in kilograms. If the field is empty, those two rows simply do not appear; the page never plugs in zero for weight.
What does “outside the formula's range” mean?
That with your measurements the formula returns a number that cannot be a body fat percentage – negative or far too large. This happens with an unusual combination of measurements or a measuring mistake. In that case the page does not print a number at all: better to show nothing than something implausible.
Why is there no BMI?
Because it is a different thing. BMI is worked out from weight and height and knows nothing about body composition: a muscular man and a person with the same BMI and twice the fat look the same to it. Here it is composition that counts, which is why the main formula needs no weight.
Is this the same as what body composition scales show?
No. Those scales send a weak current through you and estimate fat from tissue resistance, and resistance depends heavily on how much you have drunk and when you ate. It is a different method with a different error, so numbers from the scales and numbers from here will not match – it only makes sense to compare each series with itself.